Results 1 to 13 of 13

Thread: How to USe Keyless Entry Pad

  1. #1
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts

    Post How to USe Keyless Entry Pad

    Straight from the owners manual

    With the keyless entry keypad, you can:
    ˛ lock or unlock the vehicle doors without using the key.
    Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located:

    ˛ on the owner’s wallet card in the glove compartment
    ˛ taped to the computer module
    ˛ or at your dealer.

    When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation.

    Programming your own personal entry code
    To program your own code:
    1. Enter factory set code (keypad will illuminate when pressed).
    2. Press 1/2 control within five seconds of step 1.
    3. Enter your personal 5 digit code.

    Enter each digit within five seconds of previous one.
    Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase it in favor of the new code.

    If you wish to erase your personal code, use the following instructions:

    Erasing personal code
    1. Enter factory set code.
    2. Press 1/2 control within five
    seconds of step one.
    3. Press 7/8 control and 9/0 control
    at the same time within five seconds
    of step 2.
    The system will now only respond to the factory set code. Anti-scan feature The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle.

    Locks and Security
    Anti-scan will be turned off after:
    ˛ one minute of keypad inactivity.
    ˛ the remote entry transmitter UNLOCK button is pressed.
    ˛ the ignition is turned to the ON position.

    Unlocking the doors with the keyless entry system

    To unlock the driver door, enter either the factory set code or the
    personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver
    door unlocks) and press the 3/4 control within five seconds.

    Locking the doors with the keyless entry system

    It is not necessary to enter the factory or personal code prior to lockingall doors. To lock the doors:

    ˛ Press the 7/8 control and the 9/0 control at the same time.

    Activating/deactivating autolock with the keyless entry system

    Before following the activation or deactivation procedures, make sure that the anti-theft system (if equipped) is not armed, ignition is off, and all vehicle doors and liftgate window are closed.

    1. Enter 5 digit entry code
    2. Press and hold 7/8 control
    3. Press and release 3/4 control while holding 7/8 control
    4. Release 7/8 control.

    The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.
    To re-activate autolock, repeat steps 1–4.

  2. #2
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts
    Mods could you make this a sticky please

  3. #3
    2003 H/D #6809
    Name:

    bradshow's Avatar
    Join Date
    Dec 2006
    Location
    Norman, OK
    Posts
    872
    Like
    0
    Liked 0 Times in 0 Posts
    The autolock feature locks the doors once you start to move, is there a way to make the system unlock all the doors when you put it in park ?

  4. #4
    Registered User
    Name:

    2tone03harley's Avatar
    Join Date
    Jan 2004
    Location
    georgia
    Posts
    516
    Like
    0
    Liked 0 Times in 0 Posts
    ^ what he said. is there a way stew?

  5. #5
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts
    not gonna happen....at one time I was pretty sure that there was a way to make the rear doors autounlock...I still think there is via one of the nifty dandy ford super comp tools that interface with the GEM and PCM.

    The only other way is for an aftermarket alarm to control them which I have figured that mine does as my rear doors unlock automatically.

  6. #6
    Registered User
    Name:

    ws6playa's Avatar
    Join Date
    Feb 2008
    Posts
    136
    Like
    0
    Liked 0 Times in 0 Posts

    keyless entry

    is this the same for all models of fords from expediton to excursion
    thanks

  7. #7
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts
    works on my wifes 98 expedition and my 02 Harley..

    The process is called out in the owners manuals if yuo have one

  8. #8
    "Fuzion" 1986-2007 R.I.P.
    Name: Troy

    1niceharley's Avatar
    Join Date
    Nov 2004
    Location
    Haslet, Texas
    Posts
    3,917
    Like
    2
    Liked 4 Times in 2 Posts
    This also worked when I had my 05 Expedition.

  9. #9
    Registered User
    Name:

    ws6playa's Avatar
    Join Date
    Feb 2008
    Posts
    136
    Like
    0
    Liked 0 Times in 0 Posts

    the sticker on the computer

    i cant locate it on my excursion 2005 and how about the expedition 03 are they in the same area?

  10. #10
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts
    could be on GEM, could be on ECM, could be in owners manual...only other thing to do is go to ford and ave them hook the IDS up and have them tell you what the factory set code is

  11. #11
    Registered User
    Name:

    ws6playa's Avatar
    Join Date
    Feb 2008
    Posts
    136
    Like
    0
    Liked 0 Times in 0 Posts
    where is the gem located and the ecm located

  12. #12
    ResFirma Mitescere Nescit
    Name: stew

    bgstew6's Avatar
    Join Date
    Jun 2004
    Location
    Charleston, SC
    Posts
    18,059
    Like
    0
    Liked 0 Times in 0 Posts
    ecm/pcm above pasenger side kickpanel up near firewall

    Gem...under the dash up high above the steering column, creme colored box

  13. #13
    Registered User
    Name:

    Bigricci's Avatar
    Join Date
    Sep 2009
    Location
    Eva, Alabama
    Posts
    96
    Like
    0
    Liked 0 Times in 0 Posts

    Keyless Entry

    I am so glad this was posted. Just found mine under the dash next to the steering column!
    Thanks...Jim

    "Experience hath shewn, that even under the best forms of government those entrusted with power have, in time, and by slow operations, perverted it into tyranny".

    ~ Thomas Jefferson

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •