Quote Originally Posted by iHarley View Post
CAUTION, (possibly a WARNING)

Please consider the electrical requirements for this upgrade carefully!

DO NOT use the RD/BK (Red w/ Black Strip), Circuit# 1153, Driver and passenger heated seat high amp circuit, Hot at all time, 14 Gauge, Fuse F1.118, 30Amp, Pin# 3 in connection C311 to power the power seat motors / transmission. Refer to your Electrical Shop Manual. Your circuit numbers and fuse locations maybe different, those I’ve listed are for a 2003 Harley F150.

Just because the wire is hot at all times, does NOT make it a safe connection!!!

The RD/BK (Red w/ Black Strip) wire, heated seat function circuit, Hot at all time, for driver and passenger, is safety protected by a 30Amp fuse, F1.118 in the BFB (Battery Fuse Box) and IS NOT - IS NOT - IS NOT designed to carry the additional current of a power seat! That is what you are doing, if simply connecting to the RD/BK (Red w/ Black Strip) wire. Adding an addition 30Amp device to a circuit designed for only 30Amp total for now 60Amp possible!! While connecting your passenger seat to the RD/BK (Red w/ Black Strip), Driver and passenger heated seat high amp circuit, Hot at all time may work, if overloaded with seat heater(s) on and full draw on the motors, at minimum, if you are lucky, you will just blow the fuse, F1.118 in the BFB (Battery Fuse Box). OR you could damage the expensive heated seat control module, OR even possibly cause a FIRE.

The Drivers Power seat circuit, Hot at all time, is safety protected by a 30Amp fuse, F1.112 in the BFB (Battery Fuse Box).

EACH power seat regardless of the vehicle REQUIRES a separate safety protected 30Amp fuse! Please refer to wiring information for the vehicle you acquired for your power seat track.

If you don’t have a shop manual, simply refer to your vehicles Owner’s Manual. Your fuse number locations maybe different, but the circuit requirements are the same.

The correct and safest way to wire this upgrade, AND the way it’s done by the OEM of your motorized seat track is to install a separate safety protected by a 30Amp fuse for the passenger seat; there are several “Not Used” positions available. The power seat only requires one Hot at all time, 14 gauge wire, with a separate safety protected by a 30Amp fuse and a ground - It really doesn’t get any easier.

Please do not be concerned about heat vs non-heated power seat track for this upgrade, it does not make any difference and only confuses a very simple upgrade with parts which were designed for other vehicle features you don’t have, ie power lumbar, heated rear seats, cooling (climate control), etc. Don’t fret about getting the wiring harness from the donor vehicle, you don’t need it! Your connector uses Ford Wedgelock Pin Type Terminals, which are readily available, use the vacant position in your current connector housing for a new separate safety protected by a 30Amp for the power seat. KISS - save yourself some money and time. Have more options looking for your passenger power track, and don’t buy hard to find and sometimes expensive OEM harnesses / connectors / heat controllers etc!

If you have a heated passenger now, fine - leave it alone! It was installed by Ford and works safely. Simply add a new separate safety protected by a 30Amp fuse for the passenger power seat and a ground. If you don’t have a heated passenger seat now, fine! - Just add a new separate safety protected by a 30Amp fuse for the passenger power seat and a ground.

This is a great upgrade and addition to the vehicle, done properly.
Many thanks to all to this “How to”
Good point. When I did mine I used a cheap amp distribution block with dual fuses. I cut the red/blk wire on the drivers side and put the end coming from the fuse box into the in. Then I put the other cut end in one of the fused outs and plugged it back into the drivers seat. I ran a length of wire the same gauge as the red/blk wire from the other fused out over to the pass. side and plugged the connector into that seat. I know this isn't really ideal, but I feel better knowing there is a fuse there also. Both of those fuses are 30 amp also. Maybe I should put smaller amp fuses in there so they would pop there?

Another thing to ponder, in order for what you are describing to happen. You would have to be running both drivers and passenger heaters at the same time. Which I have done but my truck was equipped from factory with both. Adding the power passenger seat again you would have to be running both seats at the same time. The odds of that happening are pretty slim if you ask me. Unless you get some idiot that plays with the seat settings constantly. Which a quick backhand will fix.