Is there some trick to get this damn thing off!! I can get the bottom latch off but I can't seem to figure out how the get to the top latches. Please, it looks like sh!t, I need some help. Thanks ;c
Is there some trick to get this damn thing off!! I can get the bottom latch off but I can't seem to figure out how the get to the top latches. Please, it looks like sh!t, I need some help. Thanks ;c
'00 Corvette FRC
just went through this on my 03
mine had little plastic tabs that held it on, per someones post on here, I used a box cutter with the blade all the way out to reach through fromt he front and cut the plastic pins. They dropped out the back and the plate was off!
hope this helps!
-V
Venom, that was my response to you on the box cutter. The 2002
have 2 small bolts that must be removed at the top and have either a bolt or plastic push pin on the bottom. I think the wrench size is 8mm or 10mm.
NHTOC # 21
2003 10th Annv Torch Red Convertible Cobra
Predator/Runnin With The Devil
Billetflow 2.76, idler and 4 Pulley Kit
LFP Ported Blower
LFP Heat Exchanger
K&N FIPK
LFP Brisk Plugs
Bassani Catback/Catted X-Pipe
LFP/Kirban Shifter
MGW Shifter Handle
470HP 481.5tq new KB numbers soon
TSDUKE -
The top two tabs on that license plate bracket are about three inches long and each one has a bolt with 8mm head holding it on. It comes down from the top through the clipnut on the end of the plastic tab - requires getting under the truck to get to them. You will only lose a little skin before you're through - have fun!
:bo:
NHTOC #12
Drive Fast, Ride Hard & Have Fun
ahhh
well I'm glad Ford changed it for 03 then!
I lose enough knuckle skin as it is!
-V
so for me to take off the one on my 03 i gotta just chop it off?
My 03 had the metric bolts. 2 on the top and 1 on the tab at the bottom. It's a tight squeeze at the top, u will lose some skin.
It's a major pain in the A@@ job. It involves a lot off swearing and skin off your knuckles. ;c
2006 Lincoln Mark LT 4X4
2006 Mustang GT Coupe
]Originally posted by HD1832
TSDUKE -
The top two tabs on that license plate bracket are about three inches long and each one has a bolt with 8mm head holding it on. It comes down from the top through the clipnut on the end of the plastic tab - requires getting under the truck to get to them. You will only lose a little skin before you're through - have fun!
:bo:
Also, on the 02s, the metal nuts that are pressed on to the tabs at the top don't fit through the opening in the front bumper. I had to get a pair of needle nose and pry them off before sliding the tabs through the bumper.
'02 DSG Build #9034
Born: 6/6/02 Kidnapped: 11/30/02
NHTOC #129
i removed mine last night
what about cutting it off?? will that work??
I cut mine on the 02 and pulled the tabs out the back.
I just removed the radiator shroud and took the bolts out from the top. I almost didn't get my arm back out but didn't have to cut anything.
rhino=lmao
Yeah I am a pretty big guy and I really thought it wasn't coming out for a minute. Have to say the wife wasn't too happy about me removing my nice mirrored Rhino plate. Loved the plate, just hated the air getting blocked by it.Originally posted by musturbo
rhino=lmao
2004 Red Lightning Born: 3/16/04
Build # 2547 out of 3,781
390HP/475TQ-Torrie tuned...
1.926, 12.88 @ 107.27
Photo Gallery, click here...
2002 Blk HD #7073--> Sold