-
Registered User
Name:
LFP E-fan
can someone make a how-to for the LFP fan install?
-
World's Fastest Street HD
Name: Josh
did you buy it used? the instructions that come with them are very good and have good pics and details. only confusing part is the fuse box, but once you get which direction the picture is facing its not bad
http://www.nhtoc.com/vbforum/showthr...t=efan+install
there's the thread i put up when i first got the Efan 2 years ago. probably some tips in there or something
one tip....for the sending unit....alot of guys try to do it from under the truck and take a coolant bath
just jack the drivers side up, pull the drivers wheel off, and the sending unit goes right in front of you in the block. makes the install for that nice and quick and easy and hardly any mess at all. i lost maybe an ounce of coolant at most
-
-
Registered User
Name:
wow, thats a nice tip I will have to remember that.
I guess you are talking about installing the t-stat.
What about wiring the switch in the cab, you must drill a hole through the firewall?
-
-
#4954, 12APR01
Name:
SMOAK,
On the driver's side firewall, you will find a hole with a rubber grommet already drilled from the factory. Use that to route the wire for the manual override switch.
-
-
World's Fastest Street HD
Name: Josh
yep, like Kromie said.
Then under the dash, by where your right leg would be, there's a hole that the switch fits in perfect, and is nice and hidden and out of the way. hard to describe, somebody else could probably give you a better idea of its location, but its the perfect spot for it, the wire is the exact length you need, and no drilling
-
-
ResFirma Mitescere Nescit
Name: stew
the hole is just to the left of the Diagnostics port and on the same bracket as the diagnostic port. The Port is just below the cubby hole to the lower right of the steering wheel. Like Harley said, perfect spot, not drilling and hidden out of the way so that you dont accidently bump it.
-
-
World's Fastest Street HD
Name: Josh
-
-
Registered User
Name:
awsome! i cant wait to get this thing! Got Bilsteins to install also. Contemplating painting the calipers also.
-
-
ResFirma Mitescere Nescit
Name: stew
IMO the hardest part of the install was getting the wire loom cover off of the firewall, above the engine, to route my remote fan switch, temp sender wire and fuse box wires. Installing the temp sender into the block was a sanp and I think I spilt maybe 1/4 cup of fluid. I jacked up the drivers side of the truck, left the tire on, crawled underneath and got her done.
-
-
#4954, 12APR01
Name:
STEW,
Told you we should have taken pictures when we did your fan.!
-
-
ResFirma Mitescere Nescit
Name: stew
Yeah Yeah,,
But we jumped in there and got her done with out looking back and totally forgot about the pics. Remember I had the Camera in tow and failed to take one pic. Sorry guys!
-
-
#4954, 12APR01
Name:
Originally posted by bgstew6
Yeah Yeah,,
But we jumped in there and got her done with out looking back and totally forgot about the pics. Remember I had the Camera in tow and failed to take one pic. Sorry guys!
so now, i have to do this:
THIS POST IS WORTHLESS WITHOUT PICTURES
Better not forget it this time when we do rotors and pads this SAT. And shackles too. And traction bars.
-
-
ResFirma Mitescere Nescit
Name: stew
LOL
I will bring it,
oooo and guess what Santa brought daddy!?
-
-
#4954, 12APR01
Name:
-
-
*SOLD - but not forgotten
Name: Chuck NHTOC #291
Mods=L&S Oil Sep, Blackwood trim & mirror caps, Navi ant' base, E-brake pedal, CAI, C&L Intake & Plenum, 95mm MAF tube, SBTB, 170 T-Stat, Predator+RWTD custom tune, 8# lower, PG Ti900.7 amp, JLA XR570-CXi & Stealthbox, FTVB, Finned Trans Pan, Line of Fire LED, J-Jent Grille, RotorPro Dimpled & Slotted rotors, LED taillights, chrome door strikes, billet locks & coat hangers, ChickenEars Engine Billet package #1&2+door sills, Metco billet aux idler bracket & pulleys, LFP E-Fan, Xenarc HID heads, clear corners, Roush HID fogs, Bedrug, L' 3rd, Kenwood DDX-7017 DVD+TV+Sirrius+RevCam, Lotek dual pillar pod with AutoMeter boost gauge & DynoJet WBC, fog switch mod, UPR billet window switches and door locks, FAST overlays, LFP 58" bars, Hotchkis TVS, Bilsteins, DblG Panhard, Cervinis Cobra R hood, BFG T/A KDW 2 tires, Hawk Ceramic pads, MGP caliper covers.
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules